← All free practice sets

NO SIGN-UP REQUIRED

Free Backflow and Cross-Connection Control Practice — IPC 2021 §608 practice questions (2026)

What is the format? These ten original multiple-choice questions introduce Backflow and Cross-Connection Control Practice — IPC 2021 §608 study topics. They are practice material, not actual exam items. Official assessments may use different formats; check the current candidate guide for your credential.

What does this prepare me for? General code practice. Not aligned to any specific state exam blueprint. Check your licensing authority’s current bulletin. CodeReady does not confer a license.

What should I study? Start with protection methods and assembly selection, installation, air gaps, and testing, hazard identification and specific applications. This bank uses IPC 2021. Check the current exam objectives, adopted editions, and permitted references before planning your study.

How should I practice? Choose an answer before opening the explanation. Read the cited reference and revisit unfamiliar topics. These samples are general preparation, not jurisdiction-specific advice.

Explore full Backflow and Cross-Connection Control Practice — IPC 2021 §608 →

1 / Protection methods and assembly selection

A process connection presents a high hazard and can impose backpressure. Which listed assembly type is suitable for both conditions in Table 608.1?

  1. Pressure vacuum breaker assembly
  2. Reduced pressure principle backflow prevention assembly
  3. Double check backflow prevention assembly
  4. Spill-resistant vacuum breaker assembly
Show answer & explanation

Reduced pressure principle backflow prevention assembly

The table permits reduced pressure principle assemblies for high or low hazards and for backpressure or backsiphonage.

IPC 2021 Table 608.1

2 / Protection methods and assembly selection

Which Table 608.1 method interrupts the water path through open atmosphere instead of using check valves?

  1. Air gap
  2. Double check assembly
  3. Dual check device
  4. Reduced pressure assembly
Show answer & explanation

Air gap

An air gap physically separates the outlet from the receiving water; the other choices are mechanical devices or assemblies.

IPC 2021 Table 608.1

3 / Protection methods and assembly selection

A low-hazard process has a booster pump that can exceed supply pressure. Which listed option covers that mechanism?

  1. Double check backflow prevention assembly
  2. PVB assembly
  3. Spill-resistant vacuum breaker
  4. Barometric loop
Show answer & explanation

Double check backflow prevention assembly

A double check assembly covers low-hazard backpressure. Each vacuum-based alternative is limited to backsiphonage.

IPC 2021 Table 608.1

4 / Protection methods and assembly selection

A supplier offers a listed and labeled ASME A112.1.3 air gap fitting. How is that standard treated by the air-gap provision?

  1. It is the named standard for air gap fittings
  2. It is the standard for double check assemblies
  3. It is only a drainage pressure-test standard
  4. It establishes PVB critical-level clearance
Show answer & explanation

It is the named standard for air gap fittings

Section 608.14.1 distinguishes ASME A112.1.2 air gaps from ASME A112.1.3 air gap fittings.

IPC 2021 §608.14.1

5 / Protection methods and assembly selection

A PVB assembly is shown 8 inches above the highest downstream outlet. The installer cites the general 6-inch vacuum-breaker rule. What governs this PVB layout?

  1. Its critical level must be at least 12 inches above all downstream piping and outlets
  2. The 6-inch general statement always replaces the PVB-specific requirement
  3. Any positive elevation is sufficient
  4. The 12-inch rule applies only to double check assemblies
Show answer & explanation

Its critical level must be at least 12 inches above all downstream piping and outlets

Section 608.14.5 specifically addresses PVB and spill-resistant assemblies. Eight inches does not meet its 12-inch clearance.

IPC 2021 §608.14.5; §608.16.4

6 / Installation, air gaps, and testing

How must an RP assembly's relief opening discharge?

  1. By air gap without submergence
  2. Through a permanently capped connection
  3. Directly below standing water
  4. Into a sealed pressure vessel
Show answer & explanation

By air gap without submergence

The relief-opening requirement preserves an air-gap discharge and prevents submergence.

IPC 2021 §608.14.2

7 / Installation, air gaps, and testing

A spill-resistant vacuum breaker has not been repaired or moved since its last test. What recurring minimum still applies?

  1. Testing at least annually
  2. No further testing ever
  3. Testing only after a pressure complaint
  4. Testing once every ten years
Show answer & explanation

Testing at least annually

The recurring annual minimum applies in addition to installation, repair and relocation triggers.

IPC 2021 §312.10.2

8 / Installation, air gaps, and testing

A 2-inch effective opening is 7 inches from each of two intersecting walls. What minimum air gap applies?

  1. 6 inches
  2. 4 inches
  3. 2 inches
  4. 8 inches
Show answer & explanation

6 inches

The two-wall threshold is greater than 4 × 2 = 8 inches. Seven inches fails it, so the gap is 3 × 2 = 6 inches.

IPC 2021 Table 608.16.1 and footnote a

9 / Hazard identification and specific applications

A new fixture fitting connects directly to potable supply piping. What standard is named for its backflow protection?

  1. ASME A112.18.1/CSA B125.1
  2. ASSE 1060 only
  3. ASSE 1064 only
  4. AWWA C510 for every fitting
Show answer & explanation

ASME A112.18.1/CSA B125.1

Section 608.2 requires fixture fittings to provide protection in accordance with ASME A112.18.1/CSA B125.1.

IPC 2021 §608.2

10 / Hazard identification and specific applications

Which group is named in the second exception to water-distribution-system isolation?

  1. Deluge, preaction or dry pipe systems
  2. Every continuously pressurized antifreeze system
  3. Every wet system with chemicals
  4. Every system with a nonpotable secondary source
Show answer & explanation

Deluge, preaction or dry pipe systems

Those three system types are expressly listed. The separate requirements of Section 608.17.4.1 must also be considered where applicable.

IPC 2021 §608.17.4 exception 2

Keep the momentum.

Unlock the full bank, practice modes, and explanations.

Get the full practice bank →